u/ParisKitty

À propos de cet article

- Écologique, Hypoallergénique et approuvé par les médecins allergologues de l’arcaa

- Composition sans colorant, sans allergènes cutanés, sans isothiazolinones ou dérivés mit & bit

- Sans symbole de danger, ni phrase de risque. Emballage 100% recyclable. Fabriqué en France

Veuillez lire la description du produit si possible. Merci.

If the dirt is on the corner of the bottle, brush can fail to reach. I do use the bottle brush as well. Ball chain method is for those tough to reach areas. Chains for sink stopper is rust resistant. They are ment to get wet all the time after all. Just make sure to dry them well after each use before storing. Cream cleanser: https://www.amazon.fr/LArbre-Vert-%C3%89cologique-Surfaces-Lavables/dp/B07FN9HWMC/

To clean difficult to reach bottles, I use a length of ball chain (like the one comes with a sink stopper). You can ask a hardware store to cut it to the length you need. I pour some cream cleanser into a bottle with a chain and swirl around till all dirt is gone.

If you are certain white is the dirt (hard water deposit), you could use CLR Calcium, Lime & Rust Remover. Old toothbrush comes in handy.

Mixing baking soda (alkaline) and vinegar (acidic) neutralizes each other rendering them ineffective. Better use something like Bar Keepers Friend with non scratching nylon pad.

Layer of paper towel + bleach (3hrs +) before giving up and paint over.

I have exactly the same model. It works very well in a confined area like under the sink but not for a larger area. As for cleaning, you can put a small amount of household bleach, making sure to soak the problem area, leave it for overnight and wash the next day.

We deal with weeds by a weed burner. It will slow down the weeds (but does not eliminate). For the area where feasible, we placed a good quality weed mat and covered it with paving stones.

You might have a better chance posting at r/ifixit - subreddit for small electronic repair.

85% plus concentration of isopropyl alcohol. The rugged plastic of tool box should take it.

I stopped reading the page after this line.  It is useless to mix alkaline (baking soda) with acid (vinegar).  Quote ==>>"Start by sprinkling baking soda over the surface of the cutting board, then pour vinegar over it."<<==

Plastic blade scraper is safer than metal one. 80 % isopropanol should be OK for the paint but test it in inconspicuous area first.

Layer of paper towel + small amount of bleach. Leave 30 min before rinse. Repeat if nessary.

You might want to inspect the tiny hole that supply the gas. We had a problem with the most frequently used burner. After I cleaned the hole with a sawing needle, everything was OK.

Spay it with an oven cleaner. Place it in a garbage bag. Seal and leave 3 hours or longer. Clean with rug or paper towel. Repeat till all mess is gone. For a preventative measure, you can place a heat resistant silicone mat on it. Mat is easy to remove and clean.

I would reinforce the brocken area with flexible but strong enough plastic piece. I have a collection of such plastics salvaged from various packagings.

Bar Keepers Friend (oxalic acid), if that fails soak the cup in diluted household bleach.

Layers of paper towel. Pour bleach on it to moisten. Wait for 30 min before remove paper towels and rince. That is how I deal with a stain on my white kitchen sink. My next kitchen sink should be a commercial grade stainless steal...

After the pantry moss infestation we got last year, I now made a habit to vacuum seal grain/flour in smaller portions. I open one at a time and transfer the content to the glass jar with a tight fitting lid. I also have a moss pheromone trap stick to the pantry for precaution. So far the moss never came back.

They look like lichen to me. Pressure wash?

Insert an old credit card or guitar pick?

I just cleaned mine to spar-clean using "Dr. Beckmann - Pierre à Tout Nettoyer" and Bosch UniversalBrush. You need to remove water first using a small cup then work on the problematic area.

You can try isopropanol. 75% and up. This type of plastic should withstand it.